Athearn HO DS 40-2 - dreckige Räder

  • Hallo,


    sagt mal , sind die blue geboxten SD 40-2 überhaupt zum Fahren gedacht oder lege ich die gleich still? Bin kaum damit gefahren und schon fangen die an zu stottern und zu funken.


    Und.. ich brauche noch Metallräder als Ersatz der Dummy-Plastikräder für SD 40-2, F7, GP38-2. Was nimmt man da ?


    LG
    Holger

  • Zitat

    Original von Peter Speiser
    Hallo,
    am besten die NWSL-Räder in die powered Units, die anfallenden Athearn Räder dann in die Dummys.
    Peter


    VORSICHT
    NWSL Liefer nur die beiden Räder mit Achsstummel. Nicht das Zahnrad zum erstellen des kompletten Radsatzes. Wie bitte sollen dann die Athear-Originale in die Dummys passen?
    Ich habe das Thema gerade mit einer Powered F7 und 2 Dummy durch. Dann lieber auch gleich die passenden Räder für Dummys bei NWSL mitbestellen.

    Gruß
    Jürgen
    US-Modellbahner seit 1975 in (N). Wechsel zu H0 und DCC 1998
    Vorbild war die Penn Central und Ihre Vorgänger (PRR,NYC,NH) in H0
    Jetzt Nebenbahn/Privatbahn und DB ex Heimatort ca. 1950 - 1960

  • Zitat

    Original von canadian pacific
    Hallo,


    Und.. ich brauche noch Metallräder als Ersatz der Dummy-Plastikräder für SD 40-2, F7, GP38-2. Was nimmt man da ?


    LG
    Holger


    Antwort von NWSL zu dem Thema bei meiner F7
    ------------------------------------------------------------
    Determine which version Athearn diesel you have - an older "outside frame (metal sideframes)" or newer "inside frame (plastic sideframes)"? See the following NWSL catalog page for information and suggestions as well as the data below.


    see: page 4-16b: http://nwsl.com/Catalog/cat4-16b-v9902.pdf


    Information from the
    NorthWest Short Line model maintenance shared information databank


    See also: MODEL RAILROADER, Dec 1985, pp 94+


    GENERAL COMMENT
    We do not replace gearing in Athearn geared locomotives. The existing gearing, while not perfect, is quite good and the cost and complexity of replacement is an uneconomical alternative. The major cause of noise and operating quality shortcoming lies with the motor - in most instances, replacement of the motor with a better quality motor will result in the desired operating quality improvement.
    See the #161-4, #162-4, #163-4 and #165-4 "ATHEARN RE-POWER" kits (page 4-16c: http://nwsl.com/Catalog/cat4-16c-v0305.pdf) for pre-assembled motor/flywheel power unit with appropriate NWSL universal coupling. These units replace the original Athearn power system completely between the gearbox towers, connecting directly to the Athearn wormshaft (after removal of Athearn u-jt part from wormshaft). The #161-4 with single flywheel is suitable for all narrow hood road diesels (GP9, SD38, GE, etc.) as is the #163-4 which has double flywheels for the longer diesels such as the SD40, U-boat, FM, etc. These can also be used in "wagon top" (wide body) units (F, PA, etc.) but operating speed may be slower than desired. For the wide body diesels, the #162-4 fits and provides a better speed range (79 smph) for passenger service or the #172-4 when higher speed (130 smph) is desired. The #165-4 (and #164-4 it replaced) fit the diesel switchers.
    All units require revision of motor mount and fixing of motor in place with silicon sealant (the stuff sold as bathtub caulking, etc.) and attaching the terminal wires as appropriate for electrical connection.
    GEARS COMMENT
    One of the realities of moulded gears is that it is very difficult to make moulded gears consistently concentric due to shrinkage and warpage tendencies of plastic material as it cools and ages. Most mechanisms are made with enough slop to compensate for such problems however I assume that unless such a problem were called to Athearn's attention, they would not even know that this is a problems at this point in time. They do test run everything but presumably your (and my) standards are higher than low price, mass production economics can afford. When I investigated re-ratioing Athearn units years ago, the conclusion was that because the gears are moulded of a non standard gear form, any cut gear was going to be makeshift. We are set up to efficiently make gears under .625" diameter but over that size, our costs are considerably increased, so I don't think its practical to sell replacements. In fact, this problem is apparently rather rare and therefore it may be safe to assume that a replacement gear(s) purchased from Athearn would be satisfactory.


    Modeler Feedback Comment:
    "... my inquiry about bad Athearn trucks ... I tried your idea of replacing motors (not gearing) ... and you hit the nail right on the head ..." MD 15909 970505


    Replacement upgrade wheels: see the "Athearn half axle" wheels, #37139-4, et al. - page 4-16b of the NWSL catalog.
    page 4-16b: http://nwsl.com/Catalog/cat4-16b-v9902.pdf


    Nickel-silver upgrade wheels
    Outside Frame Inside frame Genesis
    (original) (new circa 1990)
    3/32" axle 3/32" axle 1.5mm axle
    Traditional 40"/110 #37139-4 $9.95 #37141-4 $9.95 #37191-4
    Width 42"/110 #37140-4 $9.95 #37142-4 $9.95 #37192-4
    tread 45"/110 #37144-4 $9.95


    Semi- 40"/88 #37239-4 $9.95 #37241-4 $9.95 #37291-4
    finescale 42"/88 #37240-4 $9.95 #37242-4 $9.95 #37292-4
    tread 45"/88 #37244-4 $9.95


    P:87 40"/64 #37639-4 $10.95 #37641-4 $10.95 #37691-4
    finescale 42"/64 #37640-4 $10.95 #37642-4 $10.95 #37692-4
    tread 45"/64 #37644-4 $10.95


    ****************
    Subject: Improved Operation Friday, March 22, 2002
    NWSL Team
    I have just installed your 1/2 axle wheelsets in my Athearn GP38-2, and the low speed operation has improved over 1000 %.
    Before the low speed was jerky and loss of power.
    Now with no other changes than your wheelsets the low speed operation is so smooth that I can't believe it.
    The engine will now creep.
    Thank You FD Wildomar, CA
    *****************
    Wheel size (diameter)? -
    Most Athearn diesels have 42" wheels whereas most prototype diesels (F, SD40, SW, GP, SD60M, U30-C, C30-7, P30CH, GF6C, SD70(?), SD75M, etc.) used 40" wheels.
    Some new large prototype diesels such as the SD80MAC and SD90MAC have 45" wheels and the dash 8-40CM, AC44-9 and AC4400 have 42" wheels. You choose the size you want to use.


    Inside-Outside frame?
    Original Athearn geared diesel were 'outside frame' - the axle ends entered the sideframe and supported the diesel. The sideframes were metal.
    With introduction of the SD-40, the design changed to inside frame - the axle ends do not enter the sideframes which are plastic. The GP9, F7, SW-7, FM, PA, etc. were made in the original outside frame design until upgraded in the mid 1990's to inside frame design. What have you got???


    MODELER FEEDBACK
    "Your replacement wheelsets were also part of the standard package, to eliminate the .3V drop of the Athearn sintered wheels." Larry Hanlon.


    "I also did a test mount in a Athearn Diesel of your NWSL (#161-4) motor and that model ran like the prototype." LK 990309


    Sincerely,


    F R Martin, NWSL
    206-932-1087 fax 206-935-7106 Office hours: 8am-4pm PST M-F
    fredm@nwsl.com
    latest TimeTable product information newsletter, go to: http://www.NWSL.com
    Box 16485 Seattle WA 98116-0485 USA
    Email (or via fax, fone, or mail) orders accepted, VISA/MASTERCARD/Discover/AMEX accepted. Shipping - $5 per order insured, $3 not insured (to USA addresses, more to international addresses)
    Full line catalog #0-1 (100+ pages) - $9 to USA addresses, $11 to mail addresses outside USA.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    INSTANT NEWS!


    Quik links to news releases on the NWSL.com website - just copy and paste to your web browser
    New Motor: News release on new #12270-9 mid size motor:
    released 3 December, see it on our website http://www.NWSL.com
    http://nwsl.com/Timetable%20Pages/tt20%2005Dec04.htm


    Other recently released products datasheet quik-links
    N scale: #2575-6 N scale Lifelike diesel upgrade wheels:
    http://nwsl.com/Timetable%20Pages/tt13%2025Nov04.htm
    N scale: #2675-6 N scale Kato, Atlas, Intermountain, Lifelike diesel upgrade wheels:
    http://nwsl.com/Timetable%20Pages/tt18%2014Apr04.htm


    O scale, Large Scale: News release on 0.7mod ball-bearing gearbox kits - 1:1 & 14:1
    http://nwsl.com/Timetable%20Pages/tt19%2015Oct04.htm


    HO scale: Athearn (China-bilt) R-T-R cars wheelsets:
    http://nwsl.com/Timetable%20Pages/tt17%2015Sep04.htm


    G scale: USA Trains diesel axle gear upgrades:
    http://nwsl.com/Timetable%20Pages/tt16%2021Apr04.htm


    O scale: 3-to-2 rail conversion kit, upgrade wheels choices
    http://nwsl.com/Timetable%20Pages/tt11%2016Mar04.htm


    Complete current PRODUCT LIST with prices:
    http://nwsl.com/pdf%20products.htm


    **************************************************************************************************


    Ohne Werbung:
    Bestellt habe ich die Dinger über den Sammler Service
    http://www.us-trains.com/
    Ein Satz für 6 Achsen kostet 8,95 EUR

    Gruß
    Jürgen
    US-Modellbahner seit 1975 in (N). Wechsel zu H0 und DCC 1998
    Vorbild war die Penn Central und Ihre Vorgänger (PRR,NYC,NH) in H0
    Jetzt Nebenbahn/Privatbahn und DB ex Heimatort ca. 1950 - 1960

  • Hoppla das ging ja schnell,


    dann hol ich da mir mal ein Sextett zum Test...



    ZITAT
    VORSICHT
    NWSL Liefer nur die beiden Räder mit Achsstummel. Nicht das Zahnrad zum erstellen des kompletten Radsatzes. Wie bitte sollen dann die Athear-Originale in die Dummys passen?
    Ich habe das Thema gerade mit einer Powered F7 und 2 Dummy durch. Dann lieber auch gleich die passenden Räder für Dummys bei NWSL mitbestellen.


    Mmh, kann man das Zahnrad nicht auf die Tauschachsen bauen oder die neuen Räder auf die alten Achsen?
    Die Loks sind übrigens aus der 2001 PWRS Serie.



    :=(
    Danke :love)


    Holger


  • http://www.walthers.com/exec/productinfo/53-26376
    So etwas bekommst du, und in der Mitte sitzt ein Zahnrad das beide Räder zusammenfügt. Hier 6 davon.

    Die Abbildungen sind zwar von Anderen (nicht für Athearn), aber davon gibt es bei Walthers keine Abbildung. Hast du zu deinen Loks keinen Waschzettel mehr?


    die Antriebsachse ist so aufgebaut
    Linkes Rad mit halber Achse --- Zahnrad --- Rechtes Rad mit halber Achse
    Also 3 Teile = eine Antriebsachse

    Gruß
    Jürgen
    US-Modellbahner seit 1975 in (N). Wechsel zu H0 und DCC 1998
    Vorbild war die Penn Central und Ihre Vorgänger (PRR,NYC,NH) in H0
    Jetzt Nebenbahn/Privatbahn und DB ex Heimatort ca. 1950 - 1960

  • Hi,


    ach so - jetzt liest sich der Dialog ganz anders - also braucht man jetzt Zahnräder damit Dummies besser rollen... :lach) .
    In der Explosionszeichnung anno 4/00 sieht man es nicht mit den halben Achsen. mmmh, besser erst mal zerlegen was ich da jetzt wirklich drin hab. Ist nicht die 40-2 mit den 4 Zapfen zum Rahmen sondern die welche über die Kupplungen zusammengehalten wird.
    Komische Idee mit Halbsteckachsen - müsste doch eiern wie blöd. (Smilie der sich am Kopf kratzt).


    LG


    Holger

  • Hallo,
    mir ist da noch eine Idee gekommen. Vor jahren erhielt ich mal von einem Freud einen Athearn GP60 Dummy geschenkt. Ich habe dann mir viel Fleiss und Geduld zwei Kato GP 35 Drehgestelle darunter gebastelt.
    Ich weiss, ich weiss, das sind nicht die richtigen aber damals kannte ich die Unterschiede noch nicht so genau. Was solls, auf einen halben Meter Entfernung siehts ja eh keiner und das Teil läuft zusammen mit dem Mashima Motor beinahe wie Kato :D


    Stefan


  • Zitat

    Original von canadian pacific
    Hi,


    ach so - jetzt liest sich der Dialog ganz anders - also braucht man jetzt Zahnräder damit Dummies besser rollen... :lach) .


    Nein, NWSL hat auch für Dummys komplette Achsen

    Zitat

    [
    In der Explosionszeichnung anno 4/00 sieht man es nicht mit den halben Achsen. mmmh, besser erst mal zerlegen was ich da jetzt wirklich drin hab. Ist nicht die 40-2 mit den 4 Zapfen zum Rahmen sondern die welche über die Kupplungen zusammengehalten wird.
    Komische Idee mit Halbsteckachsen - müsste doch eiern wie blöd. (Smilie der sich am Kopf kratzt).


    LG


    Holger


    Seltsamerweise eiern die nicht

    Gruß
    Jürgen
    US-Modellbahner seit 1975 in (N). Wechsel zu H0 und DCC 1998
    Vorbild war die Penn Central und Ihre Vorgänger (PRR,NYC,NH) in H0
    Jetzt Nebenbahn/Privatbahn und DB ex Heimatort ca. 1950 - 1960

Jetzt mitmachen!

Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!